How To Clone Garage Door Remote Control

by William Gates 28. August 2015 22:11

Simple 2 Step Programming Instruction

Code Clone / Copy / Duplicate Brief Instruction Summary
Step Keyfob Action LED Status
1 Code Clear Press and hold down buttons A and B on Copy Remote LED flashes once then flashes quickly
2 Code Clone Press and hold down corresponding buttons on Copy Remote and Original Remote LED flashes quickly
  Code Recovery Press and hold down buttons C and D on Copy Remote LED flashes twice or three times then flashes quickly

NOTE: Code Recovery is not necessary unless you have cleared the code by accident and need to have the previous code restored.

Code Clear

How To Clone Garage Door Remote Control - Code Clear

Press and hold down buttons A and B on Copy Remote simultaneously, LED flashes once, after approximately 5 seconds, LED on Copy Remote flashes quickly, all the transmitter codes in the memory have now been erased.

After code clear, LED will flash once and remains off when pressing any button on Copy Remote.

Code Clone

How To Clone Garage Door Remote Control - Code Clone

Place your Original Remote next to Copy Remote. Press and hold down the button on Original Remote that you wish to program onto the corresponding button on Copy Remote, and then press and hold down the corresponding button on Copy Remote. Hold both buttons down until you see LED on Copy Remote flashes quickly. This should only take a few seconds, and then you have successfully duplicated the code from Original Remote.

Repeat the above code clone procedure for buttons B, C and D on Copy Remote if required.

After successfully learned, LED will turn on and remains on when any button on Copy Remote is pressed, and the button on Copy Remote will function the same as Original Remote, the clone procedure is now complete.

Code Recovery - Optional

How To Clone Garage Door Remote Control - Code Recovery

If you have cleared the code by accident, press and hold down buttons C and D on Copy Remote simultaneously, after approximately 5 seconds, LED on Copy Remote flashes twice or three times, then flashes quickly, all the transmitter codes in memory have now been recovered.

Prerequisites & Tips

If you have followed exactly the above programming procedure, but the Copy Remote does not work with your garage door opener, there are basically two major factors to consider: Firstly, your existing remote control might not be fixed code type. Secondly, your existing remote control and Copy Remote must transmit signal on the same frequency. The frequency is factory preset to 315MHz which is the standard for radio remote control apparatus in USA and China. The frequency can be changed to anywhere between 240MHz and 960MHz if required.

The detailed prerequisites are listed below, if the above procedures don't run successfully, please check if all prerequisites are met.

  • Operating frequency of both Copy Remote and Original Remote must be the same
  • Only fixed-code model can be cloned, rolling-code model which is broadly used on cars is NOT supported
  • Code of Copy Remote must be cleared before cloning procedure

The programming Tips & Tricks are listed below, which may help you in the copying procedure.

  • Copy Remote and Original Remote should be placed close to each other during the copying procedure
  • Both remotes should be placed far from any wireless device that may cause interference in the copying procedure, such as cellphones, wireless modems and other devices
  • Check if the battery in your Original Remote is in good condition
  • Check if the Original Remote is functioning properly

Cloning of Rolling-Code Model NOT Supported: Our Solidremote Universal RF Remote Control Duplicator can clone a vast majority of fixed-code RF remote controls, in which circumstance each time when the remote control button is pressed, the same code is encoded and transmitted. While when the RF remote control is equipped with Code Hopping or Rolling-Code Technology, it's not possible to clone because these type of remote controls transmit a different code each time the remote control button is pressed for better security.

TIPS: Fixed-code model is widely used in common remote control field such as Garage Door Openers, while Rolling-Code model is widely used in high security remote control field such as Car Security Systems, but today more and more latest Garage Door Openers model are equipped with Rolling-Code Technology, so contact us for compatibility information before placing an order.

ABBREVIATION: The above instructions use Copy Remote as abbreviation of Solidremote Universal RF Remote Control Duplicator and Original Remote as abbreviation of Original RF Remote Control to be duplicated.

FEEDBACK: If you have any suggestions on our How To Clone / Copy / Duplicate Garage Door Remote Control document, please send your feedback through this Contact Form, your suggestion is greatly appreciated.

Join the conversation

comments powered by Disqus

About Solidremote Blog

Welcome to visit Solidremote Technologies Ltd official technical blog, which is focused on products we make, such as garage door and gate compatible remotes, RF wireless remote control transmitters and relay receivers.

We also provide free radio remote control design tools and calculators, your feedback is very much appreciated.

Calendar

<<  August 2015  >>
MoTuWeThFrSaSu
272829303112
3456789
10111213141516
17181920212223
24252627282930
31123456

View posts in large calendar